BS ISO 18289:2014 BSl Standards Publication Licensed copy:IPLogin,Universityof Oxford,Versioncorrectasof Ships and marine technology Navigation and shallow- water engineering vessels - Anchor winches bsi. ..making excellence a habit. BS ISO18289:2014 BRITISH STANDARD National foreword This British Standard is the UK implementation of Is0 18289:2014. The UK participation in its preparation was entrusted to Technical Committee SME/32/-/4, Ships and marine technology -Outfitting and deck machinery. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct Licensed copy: IP Login, University of Oxford, Version correct as of 02/05/2016 application. @The British Standards Institution 2014.Published by BSI Standards Limited 2014 ISBN9780580804915 ICS 47.020.50 Compliance with a British Standard cannot confer immunityfrom legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2014. Amendments issued since publication Date Text affected BS ISO18289:2014 INTERNATIONAL ISO STANDARD 18289 First edition 2014-10-01 Ships and marine technology Navigation and shallow-water engineering vessels Anchor winches Navires et technologiemarine-Vaisseaux d'ingenieriede navigation eneaupeuprofonde-Treuilsd'ancres Referencenumber IS0 18289:2014(E) TSO @IS02014 BS ISO18289:2014 IS0 18289:2014(E) COPYRIGHTPROTECTEDDOCUMENT IS02014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISo at the address below or ISo's member body in the country of the requester. ISO copyright office Case postale 56·CH-1211Geneva20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland i @ IS0 2014 - All rights reserved BSISO18289:2014 IS0 18289:2014(E) Contents Page Foreword ..iv 1 Scope ..1 2 Normativereferences 3 Terms and definitions 3.1 Technical terms. 1 3.2 Types of winches. .2 Licensed copy: IP Login, University of Oxford, Version correct as of 02/05/2016 4 Design and operation ..2 4.1 General requirements .2 4.2 Strength requirements .2 4.3 Material stresses. .2 4.4 Steel wire ropes. .3 4.5 Drum design .3 4.6 Warping-ends .4 4.7 Brakes ..4 4.8 Safety and protection 4 4.9 Speed control ..4 4.10 Operating devices 4 4.11 Drive equipment ..5 5 Detailed specification 5.1 Performancespecificationsofanchorwinches .5 5.2 Overload pull .1 5.3 Working load. .7 5.4 Nominal recovery speed .8 5.5 Light line speed. .8 5.6 Holdingload .8 6 Acceptancetests. ..8 6.1 General. ..8 6.2 Type test ..8 6.3 Individual test .9 Designation system ..10 7 7.1 Designationofproductmodels .10 7.2 Nameplate. .10 @ IS0 2014 - All rights reserved ili BSISO18289:2014 IS0 18289:2014(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies (Iso member bodies). The work of preparing International Standards is normally carried out throughIsOtechnicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with Iso, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISo/IEc Directives, Part 1. In particular the different approval criteria needed for the differenttypesof Isodocumentsshouldbenoted.Thi