ISO INTERNATIONAL STANDARD 16936-3 First edition 2005-03-01 Glass in building Forced-entry security glazing - Part 3: Test and classification by manual attack Verre dans la construction-Vitrages desécurite contre infractions- Partie3:Essaiet classificationparassautmanuel Reference number ISO 16936-3:2005(E) @ISO2005 Copyright Intemational Organization for Standardization Not for Resale ISO 16936-3:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, ISO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland Copyigh Intematilnal organization for Standardzation @ ISO 2005All rights reserved itted without ficense from IHS Not for Resale ISO 16936-3:2005(E) Contents Page Foreword iv Introductior 1 Scope. 2 Normative references 3 Terms and definitions... 4 Sampling 5 Test piece support apparatus 6 Tool set.. 7 Testteam 8 Test method.. 9 Classification and designation 10 Testreport. 11 Marking. Annex A(informative)Protectionlevel ratings 11 Bibliography ili ense from IHS Not for Resale ISO16936-3:2005(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (iSO member bodies). The work of preparing International Standards is normally carried out through ISO International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. InternationalStandardsaredrafted inaccordancewiththe rulesgivenintheISO/lECDirectives,Part2 The main task of technical committees is to prepare International Standards. Draft International Standards adoptedbythetechnical committeesarecirculatedtothememberbodiesforvoting.Publicationasan International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 16936-3 was prepared by Technical Committee ISO/TC 160, Glass in building, Subcommittee SC2, Use considerations. glazing: Part1:Testandclassificationbyrepetitiveballdrop Part2:Test and classificationby repetitive impactofahammerandaxeat roomtemperature Part3:Testandclassificationbymanualattack Part4:Testandclassificationbypendulumimpactunderthermallyandfirestressedconditions @ ISO 2005 - All rights reserved onal Organization for Standardizatior Not for Resale ISO 16936-3:2005(E) Introduction Iso 16936 assesses security-glazing products that are more familiarly known as“anti-vandal",“anti-bandit", and detention glazing products. Because there is no single test that will cover such a wide range of resistance to attack, four separate test methods are provided to assess the forced-entry resistant properties of security glazing. It is not intended that any particular test method be associated with the terms “anti-vandal" or “anti- bandit", since these terms can be only loosely defined and there is considerable overlap in their definition. The test method specified in this part of isO 16936 is a physical test using personnel and equipment and does not reproduce the conditions of real human attack. The test relies heavily on the competence and experience of personnel performing the test. The classification determined may not necessarily be reproducible and is therefore considered as comparative of various glazing constru