ISO INTERNATIONAL STANDARD 16936-2 First edition 2005-07-01 Glass in building Forced-entry security glazing Part 2: Test and classification by repetitive impact of a hammer and axe at room temperature Verredans la constructionVitragesde sécurite contre infractions- Partie 2: Essai et classificationpar impact repéte d'un marteau et d'une hacheatempératureambiante Reference number ISO 16936-2:2005(E) ISO @ISO 2005 Copyright Intemational Organization for Standardization Not for Resale ISO16936-2:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and instailed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the @ISO2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsO at the address below or ISO's member body in the country of the requester. ISO copyright office Casepostale56·CH-1211Geneva20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ISO2005-Allrightsreserved nitted without license from IHS Not for Resale ISO16936-2:2005(E) Contents Page 1 Scope 2 Normativereferences 3 Terms and definitions 1 4 Symbols (andabbreviatedterms) 2 5 Sampling .... 2 6 Apparatus 3 7 Required characteristics.. 8 8 Testmethod 8 9 12 10 Test report 12 11 Marking 12 Bibliography 13 CopyrghtIntemalnalozaandardailonghsreserved ili thout ficense from IHS Not for Resale ISO16936-2:2005(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees.Each member body interested in a subject for which a technical committee has been non-governmental, in liaison with isO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. ISO16936-2waspreparedbyTechnical CommitteeISO/TC160,Glass inbuilding,SubcommitteeSC2,Use considerations. glazing: Part1:Testandclassificationby repetitiveballdrop Part2:Testandclassificationbyrepetitiveimpactofahammerandaxeatroomtemperature Part3:Testandclassificationbymanualattack -Part4:Testandclassificationbypendulum impactunderthermallyandfirestressedconditions ISO2005All rights reserved tetionalOrganizationfoStandardizatio Not for Resale ISO16936-2:2005(E) Introduction This part of ISO 16936 assessessecurity-glazingproductsthataremorefamiliarlyknownas“anti-vandal" "anti-bandit" and “detention" glazing products. Because there is no single test that will cover the wide range of security glazing. It is not intended that any particular test method be associated with the terms “anti-vandal" or "anti-bandit',sincetheseterms canbeonlylooselydefinedandthere is considerable overlap intheirdefinition. and holes in security glazing products be avoided where possible, as these can affect the resistance of the product. The test method specified in this part of ISO 16936 does not reproduce t