BS ISO 16525-1:2014 BSl Standards Publication Adhesives Test methods for isotropic electrically conductive adhesives Part 1: General test methods bsi. ..making excellence a habit: BRITISH STANDARD BS ISO 16525-1:2014 National foreword This British Standard is the UK implementation of IS0 16525-1:2014. The UK participation in its preparation was entrusted to Technical Committee PRI/52, Adhesives. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @The British Standards Institution 2014.Published by BSI Standards Limited 2014 ISBN978 0580745676 ICS 83.180 Compliance witha British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 May 2014. Amendments issued since publication Date Text affected BS ISO 16525-1:2014 INTERNATIONAL ISO STANDARD 16525-1 First edition 2014-05-15 Adhesives Test methods for isotropic electrically conductive adhesives - Part 1: General test methods Adhésifs-Méthodes d'essaipour adhésifs aconductivité électrique isotrope- Partie1:Méthodes d'essaigénérales Reference number IS0 16525-1:2014(E) @ ISO 2014 BSISO16525-1:2014 IS0 16525-1:2014(E) COPYRIGHTPROTECTEDDOCUMENT @ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISo's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii ISO 2014-Allrights reserved BSISO 16525-1:2014 IS0 16525-1:2014(E) Contents Page Foreword iv 1 Scope 1 2 Normative references. .1 3 Terms and definitions .2 4 Lists oftest requirements 2 Tests for properties before curing ２２ 4.1 4.2 Tests for conditions of use. 4.3 Tests for properties after curing 2 Test conditions and sampling 5 3 5.1 Atmospheric conditions 3 5.2 Conditioningofthespecimens 3 5.3 Definition of lot. 5.4 Sampling. 3 6 Tests for properties before curing/drying .3 3 6.1 Appearance 6.2 Density. 3 6.3 Viscosity 3 7 Testsforconditions of use-Pot life .3 8 Testforproperties after curing .3 8.1 Glass transition temperature, Tg 3 8.2 Moisture absorption ratio 3 8.3 Modulus of elasticity 4 8.4 Surfacehardness 4 8.5 Thermal expansion 4 8.6 Moisture permeability 5 9 Test report. 5 Bibliography 6 @ IS0 2014 - All rights reserved iii BSISO16525-1:2014 IS0 16525-1:2014(E) Foreword Iso (the International Organizationfor Standardization)is a worldwidefederation of national standards bodies (Iso member bodies). The work of preparing International Standards is normally carried out through Iso technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with Iso, also takepart in the work. ISo collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the Iso/IEC Directives, Part 1.In particular the different approval criteria needed for the different types of Iso documents should be noted. This document was drafted in accordance with the editorial rules of theISo/IEC Directives, Part 2.www.iso.org/directives. Attention is drawn to thepossibilitythat some ofthe elements of this documentmaybethe subject of patent rights.IsO shall notb