ISO INTERNATIONAL STANDARD 15616-4 First edition 2008-12-15 AcceptancetestsforCO2-laserbeam machines for high quality welding and cutting Part 4: Machines with 2-D moving optics Essais de reception desmachines de soudage et de coupage de qualite par faisceau laser CO2 Partie4:Utilisationd'optiquesmobiles2D Referencenumber ISO 15616-4:2008(E) @1SO2008 ISO15616-4:2008(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In COPYRIGHTPROTECTEDDOCUMENT ISO2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, ISO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ISO 15616-4:2008(E) Foreword IsO (the International Organization for Standardization)is a worldwide federation of national standards bodies (Iso member bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has been non-governmental, in liaison with Iso, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC)onall matters ofelectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. IsO 15616-4 was prepared byTechnical CommitteeIsO/TC 44,Welding and allied processes, Subcommittee Sc 10, Unification of requirements in thefield of metalwelding. This first edition of ISO 15616-4 cancels and replaces ISO/Ts 17477:2003,which has been technically revised. Iso 15616 consists of the following parts, under the general title Acceptance tests for cO2-laser beam machinesforhighqualityweldingandcutting: Part 1: General principles, acceptance conditions Part2:Measurementofstaticanddynamicaccuracy Part3:Calibrationof instrumentsformeasurementofgasflowandpressure Part4:Machineswith2-Dmovingoptics Requests for official interpretations of any aspect of this part of sO 15616 should be directed to the Secretariat of iSO/TC 44/SC 10 via a national standards body,a complete listing which can be found at www.iso.org. INTERNATIONALSTANDARD ISO15616-4:2008(E) Acceptance tests for CO2-laser beam machines for high quality welding and cutting Part 4: Machines with 2-D moving optics 1 Scope This part of Iso 15616 provides minimum requirements for acceptance testing,using practical test methods workpiece on the platen and moving optics. This part of IsO 15616 is not applicable to CO2-laser beam machines which use an articulated robot, nor does it apply to work stations, such as a welding positioner, fixed board cutter, etc. This part of IsO 15616 does not cover hazard protection devices, such as those for d