ISO INTERNATIONAL STANDARD 15547-1 First edition 2005-11-01 Petroleum, petrochemical and natural gas industries Plate-type heat exchangers Part 1: Plate-and-frame heat exchangers thermiquesaplaques- Partie 1:Echangeurs thermiques a plaques et cadre Reference number ISO 15547-1:2005(E) @ISO2005 Copyright Intemational Organization for Standardization Not for Resale ISO 15547-1:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56·CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2005All rights reserved nited without ficense from IHS Not for Resale ISO15547-1:2005(E) Contents Page Foreword. IV Introductior 1 Scope 2 Normative references 3 Terms and definitions.. 4 General.. 5 Proposalinformationrequired. 6 Drawings and other data requirements.. 7 Design. 8 Materials ... 9 Fabrication. 10 Inspection and testing... 11 Preparation for shipment. AnnexA(informative)Recommendedpractice.. Annex B(informative)Plate-and-frame heat exchanger checklist.... Annex C(informative)Plate-and-frame heat exchanger data sheets Bibliography.... ili se from IHS Not for Resale ISO 15547-1:2005(E) Foreword IsO (the International Organization for Standardization)is a worldwide federation of national standards bodies International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75% of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 15547-1 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures systems This first edition of ISO 15547-1, together with ISO 15547-2, cancels and replaces ISO 15547:2000, of which it constitutes a technical revision. Iso 15547 consists of the following parts, under the general title Petroleum, petrochemical and natural gas industriesPlate-typeheatexchangers: Part1:Plate-and-frameheatexchangers Part2:Brazedaluminiumplate-finheatexchangers ISO 2005 - All rights reserved nalOrganizationforStandardizatior Not for Resale ISO 15547-1:2005(E) Introduction Users of this part of IsO 15547 should be aware that further or differing requirements may be needed for individual applications. This part of iSO 15547 is not intended to inhibit a vendor from offering, or the may be particularly applicable where there is an innovative or developing technology. Where an alternative is A bullet (O)at the beginning of a clause or subclause indicates a requirement for the purchaser to make a In this part of iSO 15547, where practical, US Customary units are included in parentheses for information. Copyrghtintematlinal onganizanion te standardalonights reserved without icense from IHS Not for Resale a Not for Resale INTERNATIONAL STANDARD ISO 15547-1:2005(E