BS EN ISO 15530-3:2011 BSl Standards Publication Geometrical product specifications (GPS) - Coordinate measuring machines (CMM): Technigue for determining the uncertainty of measurement Part 3: Use of calibrated workpieces or measurement standards (iSO 15530-3:2011) bsi. ..making excellence a habit. EUROPEANSTANDARD ENISO15530-3 NORMEEUROPEENNE EUROPAISCHENORM October2011 ICS17.040.30 Supersedes CENISO/TS 15530-3:2007 English Version Geometricalproductspecifications(GPS)-Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement -Part 3: Use of calibrated workpiecesormeasurementstandards(lsO15530-3:2011) Specification geometrique des produits (GPS) - Machines a Geometrische Produktspezifikation und -prufung (GPS) - mesurer tridimensionnelles (MMT): Technique pour la Verfahren zur Ermittlung der Messunsicherheit von determination de I'incertitude de mesure - Partie 3: Koordinatenmessgeraten (KMG) - Teil 3: Anwendung von Utilisation de pieces etalonnees ou d'etalons de mesure kalibrierten Werkstucken oder Normalen (ISO 15530- (ISO 15530-3:2011) 3:2011) CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. cen EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPAISCHES KOMITEEFOR NORMUNG Management Centre:Avenue Marnix17, B-1000 Brussels 2011CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15530-3:2011: E worldwide for CEN national Members. BS ENISO15530-3:2011 ENISO15530-3:2011 (E) Foreword This document (EN ISO15530-3:2011) has been prepared byTechnical Committee ISO/TC 213"Dimensional and geometrical product specifications and verification"in collaboration with Technical Committee CEN/TC 29o “Dimensional and geometrical product specification and verification" the secretariat of which is heldbyAFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the latest by April 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent ThisdocumentsupersedesCENISO/TS15530-3:2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Sweden, Switzerland and the United Kingdom. Endorsement notice modification. BSENISO15530-3:2011 ISO15530-3:2011(E) ,Versioncorrectasof16/09/2018 Contents Page Foreword Introductior 1 Scope 2 Normative references 3 Terms and definitions. 4 Symbols. 5 Requirements.. 5.1 Operatingconditions 5.2 Similarityconditions. 6 Principle of the uncertainty evaluation using calibrated workpieces. 7 Procedure.... 7.1 Measuring equipment 7.2 Execution..... 7.3 Calculation of the uncertainty.. 7.4 Applying the substitutionmethod:special considerations .9 8 Reverification of the measurementuncertainty.... 9 9 I