ISO INTERNATIONAL STANDARD 15136-1 Second edition 2009-11-15 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 1: Pumps Industriesdupetrole et dugaz naturelPompesdefonda cavites progressantespouractivationdespuits- Partie 1:Pompes Reference number ISO 15136-1:2009(E) ISO2009 ISO 15136-1:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTEDDOCUMENT ISO2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, ISO's member body in the country of the requester. ISO copyright office Case postale56·CH-1211Geneva20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ ISO 2009 - All rights reserved ISO 15136-1:2009(E) Contents Page Foreword. Introduction. .vi 1 Scope.. 2 Normative references. 3 Terms and definitions. 4 Abbreviatedtermsandsymbols .8 5 Functional specification.. 5.1 General... 10 5.2 PcPtypedescription 10 5.3 Functional requirements 5.4 Design validation.. .14 5.5 Product functional evaluation 15 5.6 Quality control grades 15 5.7 Additional documentation .... 15 5.8 Additional requirements. 15 6 Technical specification. .15 6.1 General 15 6.2 Technical characteristics.... 16 6.3 Design criteria..... .16 6.4 Dimensional information 17 6.5 Performance ratings.. 18 6.6 19 6.7 Design validation. 19 6.8 Functional evaluationrequirements.... 6.9 Allowable design changes.... 19 6.10 Scalingofdesignvalidation. 20 7 Supplier/manufacturerrequirements......... 20 7.1 General 20 7.2 Documentationand data control 20 7.3 Product identification....... 7.4 Quality.. 23 7.5 Rawmaterialscertification. 25 7.6 Additionalprocessesappliedtocomponents. 25 7.7 Traceability..... 7.8 Calibration systems 26 7.9 Examination and inspection. 26 7.10 Manufacturing non-conformance. 7.11 User/purchaser complaint returns. 31 7.12 Product functional testing... 31 8 Repair. 31 9 Shipping, handling and storage.. 31 9.1 General 31 9.2 9.3 .32 9.4 Storage ...... 32 AnnexA(normative)Requirements forprogressing cavitypump elastomers. 34 @ ISo 2009 - All rights reserved ili ISO 15136-1:2009(E) AnnexB (normative)Design validation AnnexC (normative)Functional evaluation AnnexD (informative)Optional informationforPcP elastomertestingand selection AnnexE (informative)Installationguidelines.. AnnexF(informative)Operational guidelines AnnexG(informative)SupplementalinformationforPcPperformancecharacteristics... AnnexH(informative)Exampleuser/purchaserPcPfunctionalspecificationform .76 Annex I (informative) Analysis after use..... AnnexJ(informative)Selection and use of drive-string equipment inPcP applications.. AnnexK (informative)Repairand reconditioning . ...100 AnnexL(informative)Auxiliary equipment 103 Bibliography. 108 @ ISO 2009 All rights reserved ISO15136-1:2009(E) Foreword IsO (the International Organization for Standardization)is a worldwide federation of national standards bodies (iSO member bodies). The work of preparing International Standards is normally carried out through ISO non-governmental, in liaison with IsO, also take part in the work. IsoO collaborates closely ywiththe International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the techni